|Top Width:||13mm||Angle (°):||40°|
8mm Thickness rubber toothed belt,
13mm Wide rubber toothed belt,
8mm Thick rubber drive belts
Rubber Type A V-Belt Wrapped Rubber V Belt For Washing Machine V Belt
A brief introduction to the details of the installation triangle need to be mastered
If the distance between the two shafts is adjustable, the distance between the two shafts should be shortened, and the belt should be adjusted as needed. If the distance is not adjusted by the two shafts, a triangle can be set into the groove of the wheel, and then change to another pulley, Triangular tape, use a set of triangular tape in the same way.
V-belt manufacturers do not use hard prying and hard pull to prevent the surface of the V-belt from stretching or loosening. When the pulley is not installed, the two upper pulleys need to be aligned, otherwise it will form a unilateral operation of the triangular tape, which will cause serious wear and reduce the triangle. The use of tape. It is necessary to check whether the tightness of the triangle tape meets the requirements.
The V-belt is easy to slip, and it also increases the wear of the triangle, or does not transfer power; too tight, not only will deform and elongate, and the damage will be simple, but also due to the stress will form the clutch bearing of the main bearing and accelerate the wear of the triangle.
V-belt manufacturers do not mix the new and the old. Double or more than three triangles need to be changed. The adjustment mode of this triangle should be selected. The triangle should make the air tightness of each group consistent. It is not allowed to mix the old and the new or reduce the number. Otherwise, the old and new triangles are balanced, and even the old triangle does not work, which affects the power transmission and shortens the life of the triangle.
Belt drives mainly include: flat belts, triangle belts, and synchronous toothed belts. The three and three have national standards. However, due to the change of the transmission ratio of the pulley, the power is large. Without corresponding national standards or national standards, all content cannot be covered, but The scope of selection, use conditions, design methods, etc. determined by national standards.
|Type||Top width(mm)||Belt Thickness (mm)||Angle (°)||Production scope (lnch)|
|Can be customized according to customer requirements|
Henan Shuangli Rubber Co., Ltd. is a scientific and technological company integrating research, development and production of triangle belts. It has more than 310 employees.The factory covers an area of 30,000 square meters and a building area of 15,000 square meters,and it’s only one Triangle belt manufacturer in north Henan. It won the honorary titles successively over the years,such as the National Export-oriented of Advanced Units and the Key Protection Enterprises in Henan Province,the Contract-abiding and Trust-worthy Enterprise, Credit Henan AAA Credit Enterprise. In 2017, it passed the certification of ISO9001, ISO14001, OHASA18001 International Quality System, environmental,occupational,healthy and safety certification.The company has 2 national patents currently. In 2015, it was rated as a famous trademark in Henan Province. In 2019, there was no blind spot in the coverage of cities and counties nationwide. At the same time, it was selected as one of the top ten brands of the national triangle belt.
The company’s products are sold by agents all over the country with the advantages of super high quality and complete specifications. The products are sold in Henan, Hebei, Shandong, Shanxi, Hunan, Hubei, Guangdong, Guangxi Jiangxi, Hainan, Ningxia, Heilongjiang, Jilin, Liaoning, Inner Mongolia, Xinjiang, Lhasa and all major provinces, cities and counties, and autonomous regions across the country, they are also exported to Laos, Myanmar, Pakistan, Kyrgyzstan and other countries, and have been trusted and praised by the majority of sellers and users.
Triangle belt is also called V belt, also known as the cloth V belt
The triangle has two kinds of special core structure and rope core structure. The core, usually the band core, is twisted or woven with fiber. Special belt core is composed of polyester toughened brown silk, good adhesion, flexure resistance, high strength, no extension, its service life is 5-10 times of the rope core structure triangle belt.
3. Classification (by model)
Triangle belt by model can be divided into: usually V belt and narrow V belt
Usually v-shaped triangular belts are divided into seven grades: Y, Z, A, B, C, D and E
Narrow V bands are divided into usually narrow V bands and strong narrow V bands.
Usually narrow V with SPZ, SPA, SPB, SPC four models.
Strong narrow V with XPA, XPB, XPC
A combination of V bands, several of the same common V bands or narrow V bands working together. There's 3V, 5V, 8V and so on.
4. Model (usually model of triangular belt)
The section area of Type O, Type A, Type B, Type C, Type D and Type E tapes is gradually expanding.
When the top width and thickness are determined, the wheel groove of the belt pulley of the triangle belt can be confirmed. On the contrary, the wheel groove of the belt pulley can be confirmed and the type of the belt that should be used (A/B/C..) can be confirmed. .
Ld: Reference length. When the triangular belt rotates and bends around the pulley, the layer whose length and width remain unchanged is called the neutral layer. Under the specified tensioning force, the circumference measured along the neutral layer of the triangular belt is called Ld, the reference length
La: Outer circumference
Li: The inner circumference
Lw: Nodal length is the midline length of the triangle belt
Contact Person: admin